国产亲妺妺乱的性视频播放,9797WWW成人影片,99精品国产在热久久无毒不卡 ,西方37大但人文艺术人山踪林

Seer 還沒完成生產，就搞HoloSeer。 我定的Seer 已經4個月還沒送來，也沒消息。Email也沒回復。你是再騙咋們的錢嗎！

這篇要是有視頻就好了

是的，請談談大家對Kickstarter的。每個人有得到，因為沒有通訊或更新的憤怒。他們只是想知道，如果你還在工作的先知和問題所在位置。有人還想在中國的更新了。請他們交談和大量的憤怒將下降。

希望如此， 因為我不是個BACKER， 我是從您的網站用PAYPAL向侯柏丞訂購您的產品。有關SEER的資料已經從網站撤除，沒收到任何email update訊息， 而且INVOICE上顯示會在2015九月份交貨。請發email跟顧客交代。

Devon Montano, if you are reading this, can you explain what is the latest update is saying on Kickstarter, or perhaps copy/paste it here? Because Caputer is not sending emails to the rest of the funders outside of kickstarter campaign.

The last 2 updates that they have sent us. January 13, 2016 Dear Backers, It is a big regret that you were unable to share any information with us about the planned release of HOLOSEER prototype prior to CES 2016. As you may understand, our primary investors asked the HOLOSEER team to keep the HOLOSEER project a top secret over the past months. However, we could have left to you supporters more implications about the existence of HOLOSEER at least several hours before the opening of CES 2016. We are very sorry, although SEER team is making constant efforts to overcome the manufacture difficulties which you know from our previous statements, the introduction of mass production is so slow that the SEER headsets are not deliverable until the widely reported release of HOLOSEER prototype at CES 2016 in the last week. We promise that the SEER team should keep communicating with all you SEER supporters about the SEER manufacture issues including optical mould failure and possible refabrication, especially those who still want to wait for the success of SEER. Best regards, Team SEER -------------------------------- December 4, 2015 Dear Backers: After processing the optical surface of the mould, we had completed the fabrication of the optical lens mould which risks were never underestimated. Then a pilot production of the plastic lens has been prepared and run until the produced free-form lens was found to be deformed. It is a big regret that the serious lens deformation may be caused by several adverse factors. To identify the mould failure, we carefully reviewed the mould design and the plastic injection process. We found the deformation could get improved in sever ways, such as uniform heating and cooling, uniform plastic stream around the inlets, controlled ripples, less external forces and a greater lens thickness. Therefore，we would first try to repair the mould and test new plastic injection processes. That means we should revise the mould design and re-machine the optical surface of the current mould. As re-polishing the mould surface is highly sophisticated, the repairing work has to be carried out at a state-of-the-art facility depending upon its availability determined by out sourcing partners. We estimate the phases of redesign and verification would take us two or three weeks, and the re-fabrication of the mould could take at least two more weeks. After that, another pilot lens production should be examined. A thicker free-form lens will be resulted and less deformation expected. To minimize the expenses and the risks, we hope you give a little more time to our team and our suppliers. We should discuss the solutions deeply with our partners, so that fine products will be delivered to you supporters. The good news is that we improved the coating technology and developed new suppliers. The new coating on the free-form lens comprised of two more layers, leading to a higher transmission rate, a sharper image display, and reduced finger prints contamination. We're sorry for the delay again, but we are always responsible to our supporters. Of course, we will offer you the high quality products. In the meanwhile, some greater technology is also under our development. We want to give more surprise to you supporters, and hope to have your constant support. Best regards, Team SEER

請回復Seer的進展。奧張天天都有登入kickstarter戶口、但沒評論。

What is the latest update on kickstarter? I still havent receive the email.

已經一個月沒消息，請回覆進展。

這周模具供應商的工程師才上班，已經開始在弄；鍍膜嘗試了一爐新工藝；

看了最近的IT時報，同意說Seer的VR技術不是山寨，但Seer AR大概還需要多久的時間才能進行生產？鍍膜還在研究或修復中？等待您的消息……

是不是應該更新進展

唯！沒有消息，請交貨！